Wednesday, November 27, 2013

BC Fab's 2013 Holiday Special!


We've launched our annual Holiday Special, and there's a bunch of deals to help you get that project finished this winter!

There's 10% off on 4 link kits, airbags, and more.  Plus, every order over $100 ships for FREE!

Visit us at www.bcfab.com, get your orders placed, and have a great holiday season!

Thursday, November 14, 2013

1967 Lincoln Continental Convertible - Full Air Suspension Installation - Part 4 (The Payoff!)

You saw the car at stock height. You scrolled through a bunch of pictures as we pulled this beautiful Continental apart.  Now it's time to see how it all came together!













I've never wanted to drive off with someone's car so badly!  This Conti rides like a dream, lifts to around stock height, and drops just inches off the ground without cutting the floor in the rear!  The AccuAir eLevel height control system brings the car to a safe ride height at the touch of a button.  And the components in the trunk are mounted discretely, too:

 We mounted the air tank and compressors to a sheet of carpeted MDF, and arranged them so the factory spare tire cover fits over everything.


Thanks for reading through this installation!  If you have any questions about the Lincoln Continental air suspension kits we offer, or have a different project you're working on, visit us at www.bcfab.com!

1967 Lincoln Continental Convertible - Full Air Suspension Installation - Part 3

My last post covered installing air suspension on the front of a 1967 Lincoln Continental.  This one will cover the rear suspension.  These cars feature a unibody construction with leaf springs locating and suspending the rear axle, so they present some unique challenges when it comes to installing airbag suspension.
We created a link suspension that is designed to tie into the strongest parts of the factory subframe, and incorporates an upper crossmember with the airbag mounts integrated.  This makes installation as easy as possible, with only six holes drilled into the car and simple welding on the rear axle housing required...  Anyway, a picture's worth a thousand words, right?

The stock leaf springs were removed, along with the hanger brackets and shackles. 
The leaf spring mounts on the axle were cleaned up of rust and paint in preparation for welding as shown.

Our lower link bracket bolted in place of the factory spring hanger, and the lower link bar was bolted to it.


The lower link bracket on the axle side was welded onto the stock spring perch.


To make clearance for the crossmember, airbags, and upper 4 link bars, the mufflers needed to be removed.  There is still a pair of large mufflers at the rear of the car, so this Lincoln will still have a nice quiet system.

There is a sheetmetal bracket under the floor that needed to have a section cut out of it to make way for the upper crossmember.  This bracket isn't structural- it's just where the bump stop on the axle hit when the car bottomed out.

The crossmember was raised into place against the subframe rails.  There is a hole in the side brackets that matches up with a hole in the subframe, so we positioned the crossmember using that and marked the three holes on each side to be drilled.


The holes were drilled out, and reinforcing sleeves were placed into each hole to give the crossmember more strength.


At this point, we bolted the airbags to the crossmember and bolted everything to the subframe. 



The bolt closest to the airbag needed to be ground down to prevent rubbing.

Now that the crossmember was bolted in, we installed the upper and lower link bars.  After some careful measuring, the upper link bar tabs were welded to the axle housing as shown:

The 4 link was now complete!




A quick trip to the exhaust shop down the street, and new piping was run around the suspension.

Our customer wanted to mount as much of the system as possible underneath the car, so we were able to find homes for the AccuAir VU4 valve manifold, eLevel ride height control system, and iLevel iPhone add-on module against the bottom of the floor.  Lots and lots of wire and air line snaked all around underneath, but the only pieces that ended up in the trunk were the air tank and compressors, with a single air line and a pair of wires the only connections passing inside.


The rear ride height sensors were mounted to the side of the subframe and down to the lower link bars.
 To help conceal the system's wiring, we fabricated some sheetmetal panels to keep everything as tidy as possible.

That's about it for the underside of this car...  If you've stuck around this long, check out Part 4 for some shots of the finished product!

1967 Lincoln Continental Convertible - Full Air Suspension Installation - Part 2

With the Conti on our rack and the wheels off, we got started with the front suspension.  Here's a couple shots of the stock setup:



The first step was to remove the stock shocks and coil springs.  There's actually enough room for the airbag in the upper spring pockets, so no cutting is required! 


We unbolted the rubber bump stops on the control arms, and the front was ready for our brackets:


Travis ground the lower arms down to bare metal along the edges of the spring pocket, and our lower airbag mounting plate was welded into place.


After a coat of paint to cover the bare metal, the airbags were bolted to the upper and lower mounts, and the upper mounts were bolted into the spring pockets.  We ran 3/8" DOT-approved air brake line for this installation.



With the airbags in place, we installed shocks on the outside of the arms.  Clearance was a bit tight, so the upper control arm needed to have a small notch cut into it to make way for the shock body.  A lower stud was bolted to the lower control arm, and an upper tower was bolted to the side of the frame as shown:





The last part of the front suspension work is the height sensor for AccuAir's eLevel height control system.  We decided to hide this inside the frame in front of the control arm:


A couple of hours routing air lines and wiring, and the front suspension was all set!  I'll cover the rear suspension installation and more of the plumbing and wiring in Part 3.  Thanks for looking!